2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N Silicon NPN Transistor. Data Sheet. Description. Semicoa Semiconductors offers: • Screening and processing per MIL-PRF Appendix E. DATA SHEET NPN switching transistor in a TO metal package. collector- emitter voltage open base. 2N −. V. 2NA. −.

Author: Mazukus Gom
Country: Laos
Language: English (Spanish)
Genre: Love
Published (Last): 6 December 2010
Pages: 266
PDF File Size: 19.36 Mb
ePub File Size: 11.1 Mb
ISBN: 262-4-13277-225-2
Downloads: 99937
Price: Free* [*Free Regsitration Required]
Uploader: Dale

2N2219 Datasheet, Equivalent, Cross Reference Search

Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. The value of this current can be calculated by the required amount of current that will be consumed by the load.

However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum transostor from the transistor.

So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right transisto for your project. But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle.

2N Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

So the value if R B will be. Submitted by admin on 21 June Current Drains out through emitter, normally connected to ground.

  ANEURISMA DISECANTE DE LA AORTA ABDOMINAL PDF

This stage is called Saturation Region. TL — Programmable Reference Voltage. Complete Technical Details can be found at the datasheet given at the end of this page. Dagasheet this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. Where h FE, is the current gain of the transistor which in our case is When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

Amplifier modules like Audio amplifiers, signal Amplifier etc.

2N Datasheet(PDF) – NXP Semiconductors

To make this current flow through the transistor the value of base current I B can be calculated using the below formula: Where Vcc is the voltage on which the load 2n22119 and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula:. The 2N is a NPN transistor and is normally used as a switch in many circuits. Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits.

  COMO ORAR EN EL ESPIRITU JUAN BUNYAN PDF

But this calculation will lead to the closest value to start with. As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on.

In our case for a collector current of mA we have to pass a base current of 16mA. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin. This resistor is connected to the base pin of the transistor to limit the current flowing through the base.

So to calculate the resistor value of the base we can use the formulae.

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. Here lets us assume the load here consumes around mA maximum so our collector current I C mA.

Another important thing to keep in mind, while using a transistor datasjeet switch is the base resistor. Current flows in through collector, normally connected to load.

Technology