An Antifuse programming technology is predominantly associated with _____. Antifuse technology is nonvolatile, so it is live at power-up and programming services, either from Actel or from other vendors, are also used. recommended programming practices for antifuse devices. For SoC Antifuse technology is nonvolatile, so it is live at power-up and inherently very secure.

Author: Disar Zulugal
Country: Slovenia
Language: English (Spanish)
Genre: Education
Published (Last): 27 May 2018
Pages: 404
PDF File Size: 11.73 Mb
ePub File Size: 15.82 Mb
ISBN: 744-1-73129-309-9
Downloads: 56935
Price: Free* [*Free Regsitration Required]
Uploader: Garisar

Zener diodes can be used as antifuses. Programmin are best known for their use in mini-light or miniature style low-voltage Christmas tree lights. Each individual street-lamp was equipped with a film cutout ; a small disk of insulating film that separated two contacts connected to the two wires leading to the lamp.

This rapidly causes the antifuse to short out the blown bulb, allowing the series circuit to resume functioning, albeit with a larger proportion of the mains voltage now applied to each of the remaining lamps.

The resulting resistance of the junction is in the range of 10 ohms. By this approach, it is possible only to lower the value of the resulting resistor. In the same fashion as with the Christmas lights described above, if the lamp failed, the entire voltage programminf the street lighting circuit thousands of volts was imposed across the insulating film in the cutout, causing it to rupture. May Learn how and when to remove this template message.

They are historically used especially with bipolar processes, where the thin oxide needed for dielectric antifuses is not available. They may be less susceptible to alpha particles which can cause circuits to malfunction. This page was last edited on 7 Julyat Because the series string would be rendered inoperable by a single programmign failing, each bulb has an antifuse installed within it.

The antifuse is made using wire with a high resistance coating and this wire is coiled over the two vertical filament support wires inside the bulb.


In a similar fashion to that of Christmas tree lights, before the advent of high-intensity discharge lampsstreet light circuits using incandescent light bulbs were often operated as high-voltage series circuits. Dielectric antifuses employ a very thin oxide barrier between a pair of conductors.

Certain programmable progrxmming devices PLDssuch as structured ASICsuse antifuse technology to configure logic circuits and create a customized design from a standard IC design.

A standard NPN transistor structure is often used in common bipolar processes as the antifuse. The terminals of the antifuses are usually accessible as bonding pads and the trimming process is performed before wire-bonding and encapsulating the chip.

Antifuse – Wikipedia

In this way, the failed lamp was bypassed and illumination restored to the rest of the street. Also circuits built via the antifuse’s permanent conductive paths may be faster than similar circuits implemented in PLDs using SRAM technology.

An antifuse is an electrical device that performs gechnology opposite function to a fuse. Progrsmming Christmas lights, the circuit usually contained an automatic device to regulate the electric current flowing in the circuit, preventing the current from rising as additional lamps burned out.

Please help improve this article by adding citations to reliable sources. A specialized structure optimized for the purpose can be employed where the antifuse is an integral part of the design.

Formation of the conductive channel is performed by a gechnology breakdown forced by a high voltage pulse. The conductive shunt therefore does not compromise integrity and reliability of the semiconductor device.

From Wikipedia, the free encyclopedia. When the bulb blows, the entire mains voltage is applied across the single blown lamp. Antifuses may be used in programmable read-only memory PROM. Articles needing additional references from May All articles needing additional references. Each bit contains both a fuse and an antifuse and is programmed by triggering one of the two. Unsourced material may be challenged and removed.


Antifuse programming technology – FPGAs

This programming, performed after techbology, is permanent and irreversible. The larger, traditional, C7 and C9 style lights are wired in parallel and are rated to operate directly at mains voltage. The parallel resistors cannot have too low value as that would sink the zapping current; a series-parallel combination of resistors and antifuses is employed in such cases.

For example a precision resistor can be manufactured by forming several series resistors with Zeners in parallel oriented to be nonconductive during normal operation of the device and then shorting selected Zeners to shunt the unwanted resistors.

The spike is formed on and slightly below the silicon surface, just below the passivation layer without damaging it. Amorphous silicon is a material usually not used in either bipolar or CMOS processes and requires an programminy manufacturing step. This article needs additional citations for verification.

Antifuse programming technology – FPGAs

The p-n junction that serves as such diode is overloaded with a current spike and overheated. Programmming Corporation refers to their antifuses as “ViaLinks” because blown fuses create a connection between two crossing layers of wiring on the chip in the same way that a via on a printed circuit board creates a connection between copper layers. Ordinarily for operation from mains voltagesthe lamps are wired in series. Occasionally, the insulation fails to break down on its own, but tapping the blown lamp will usually finish the job.

Views Read Edit View history. The insulation of the antifuse wire withstands the ordinary low voltage imposed across a functioning lamp but rapidly breaks down under the full mains voltage, giving the antifuse action. This technology has many applications.