Designed for the contractor, the CPS MK II feature 2-RU chassis, Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on via remote contact closures, rear panel attenuators, and a switchable 50 Hz high-pass filter. Like the CPS multi. Two-Channel Models CPS, CPS, CPS, and CPS CPS2.x rear view. Remote power-on contact. 1. Programmable power-on timer. 2. Module slot for. Buy Electro-Voice CPS 2-Channel Power Amplifier for RCM IRIS-Net Remote Control Module (W, 4 Ohms) Review Electro-Voice CPS

Author: Mikarg Mazuzshura
Country: Reunion
Language: English (Spanish)
Genre: Finance
Published (Last): 10 July 2014
Pages: 170
PDF File Size: 3.38 Mb
ePub File Size: 18.4 Mb
ISBN: 748-7-64926-484-3
Downloads: 84042
Price: Free* [*Free Regsitration Required]
Uploader: Dounris

In DUAL mode, the two channels of the power amplifier work cpe2.9 from each other. The terminals marked with are hazardous live and the external wiring connected to these terminals requires installation by an instructed person or the use of ready-made leads of cords.

Otherwise, a 6 dB drop in level could result. When installing the power amp in a case or rack system, attention should be paid to these details to provide sufficient ventilation.

Electrovoice contractor precision cps2t: Amplification is set via input level control of channel 1 only. By pressing ‘print’ button you will print only current page. Whenever possible, using balanced audio signal feeds at the input of the power amplifier evv always preferred.

CPS2.9 MKII

Extremely high voltages can be present at the output. Also See for CPS2. The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier. Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.

Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier. Brackets for securing the power amplifier are available as accessories. Enter text from picture: For pricing options and packages, contact us at Page of 24 Go.

  CINESIOLOGIA OMBRO PDF

Electro-voice CPS Manuals

A soft start circuit compensates mains inrush current peaks and thus prevents triggering AC mains fuse when switching on the amplifier. Failure to do so may result in damage to the power amplifier as well as to the rack case. Turning the control to the right increases and turning it to the left decreases the volume. Do not modify this unit! Please read and follow the instructions provided in the documentation that you have received together with each extension module. Connect the power amplifier only to a mains network, which corresponds to the requirements indicated on the type plate.

Table of Contents Add to my manuals Add. F reserved Table 4. The connected speaker systems must be able to handle such voltages. This manual also for: The audio signal has to be applied to the input connectors of channel 1, amplification is set via input level control of channel 1 only.

Speaker system switch-on is delayed by approximately 2 seconds via output relays, effectively suppressing any possible power-on noise, which otherwise might be heard through the loudspeakers.

Additionally securing the amplifier at the rear becomes necessary, if the rack case in which the power amplifier has been installed will be transported. Only the provided power cord may be used.

Following table shows possible switch settings and corresponding delay times.

Electro Voice

Electrovoice compact precision cps: Please also see following illustration. The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintance servicing instructions in the Mains Switch The Mains Switch on the front panel separates the power amp from the mains.

  LIBRI CARTOMAGIA PDF

Show all Contractor precision cps2. Set the switch to the OFF position if no attenuation of low csp2.9 audio signals is required. Introduction 1 Introduction 1. The power drawn from the mains network is converted into output power to feed the connected loudspeaker systems and into heat.

Comments to this Manuals Your Name. The difference between power consumption and dispensed power is called power dissipation P d.

The ground lift switch allows eliminating noise loops. The audio signal has to be applied to the input connectors of channel 1.

Whenever possible, using balanced audio signal feeds at the input of the power amplifier is always preferred. To print the manual completely, please, download it. Attach the power amp with its frontal rack mount ears using 4 screws and washers as shown in following illustration.

Please take time to consult this manual so that you can understand all the features built into your Electro-Voice amplifier and fully utilize all its performance capabilities. Due to their immunity against external interference sources, such as dimmers, mains connections, HF-control lines, etc. The amount of heat resulting from power dissipation might remain inside of a rack-shelf and needs to be diverted using appropriate measures. Make sure to completely read and fully observe power rating specifications of the speaker systems to be used and to check them against the output power capacity of the power amp.

Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.

Photos