Industries du pétrole et du gaz natruel — Équipement de fond de trou — Accessoires de complétion. STANDARD. ISO. First edition. Products covered under ISO , ISO , ISO , ISO , ISO , ISO , ISO ‑2, ISO , and ISO ‑1 are not included. STANDARD. ISO. First edition. Reference number. ISO (E). This is a free 6 page sample. Access the full version online.
|Published (Last):||15 March 2015|
|PDF File Size:||17.67 Mb|
|ePub File Size:||1.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
Completion accessories shall not be rated for the following functionalities without meeting the requirements of Annex D for the selected design validation grade: Functional test data shall be recorded, dated and signed by the qualified person performing the tests.
Validation test results and dimensional test results shall be approved by a qualified person other than the person performing them and records of the results shall become a portion of the design documentation. The bubble rate shall not increase during the hold period.
Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Design changes identified as non-substantive shall include documented justification.
Petroleum and natural gas industries- Downhole equipment …
Read more about subscriptions. These include requirements for documentation and data control, product identification, quality control, functional testing, repair, redress, shipping, and storage. Documents and data may be in any form of type of media, such as hard copy or electronic media. ID drift shall only apply to completion accessory IDs not designed as sealing surfaces sealbores.
Verification results shall be approved by qualified person and records of the results shall become a portion of the design documentation.
ISO CD 3. These requirements and operating conditions may be conveyed by means of a dimensional drawing, data sheet or other suitable documentation.
BS EN ISO 14998:2013
A web subscription provides an easy and secure access to standards, and you are guaranteed to always have the latest edition.
Installation and maintenance of these products are outside the scope of this International Standard. The single specified design validation grade applies to all validation testing per Annex A thru Annex D, as applicable. ISO CD 7. Rated performance envelopes can have ratings of zero for pressure if applicable. Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work. If the rated performance envelope is a straight line, then test to the end points that define the maximum operational limits.
This standard does not cover the connections to the well conduit. If the completion accessory is also rated for any of the other functionalities listed in Table 1, then the requirements of these annexes shall also be met for the same validation grade as the Annex A testing. The material sample shall experience the same heat treatment process as the component it qualifies.
The moment new editions of the standards you monitor are released, changes are made, or appendixes are published, you will be alerted by email.
Completion accessories shall not be rated for any of the functionalities isso by Annexes B-D without meeting the validation test requirements of the appropriate Annex for the same validation grade as the Annex A testing. These ido shall address the protection of: Pressure-measuring devices shall be: Quality acceptance criteria ISOQuality management systems — Fundamentals and vocabulary ISONon-destructive testing — Qualification and certification of personnel ISOPetroleum and natural gas industries — Steel pipes for use as casing or tubing for wells 14989all partsPetroleum and natural gas industries — Materials for use in H2S — containing environments in oil and gas production 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO and the following apply.
ISO in English | Download PDF |
OD dimensional inspection shall verify that the entire OD of the assembly is less than, or equal to, the maximum specified OD. Table 1 — Design validation grades Validation Annex A: The complexity and severity of the validation testing increases as the grade number decreases. If the envelope covers two or more products that are used together down-hole, then this shall be stated on the envelope.
This is not meant to be an all inclusive list of completion accessories covered by this standard, just a representative sample. This control shall provide for 1499, documentation, evaluation, segregation when applicableand disposition of non-conforming assemblies or components. Technologies for measuring and testing equipment with verifiable accuracies equal to or better than those listed in this International Standard may be applied with appropriate documentation and when approved by qualified person.
Completion accessories shall not be rated for stroke length 3. For safety, the shear device can be replaced with a stronger shear device that can adequately withstand the maximum shear load. 144998 accessories shall not be rated for the following functionalities without meeting the requirements of Annex B for the selected design validation grade: If no leakage occurred, this shall be clearly stated.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation. The following information shall be included as a minimum: Calibration intervals for pressure-measuring devices shall be a maximum of three months until documented calibration history can be established.
Inspection and classification of drill stem elements  ISOPetroleum and natural gas industries — Drilling and production equipment – Drilling and production equipment – Part 1: Webprint Printed and bound. Attention is drawn to the possibility that some oso the elements of this document may be the subject of patent rights. The work of preparing International Standards is normally carried out through ISO technical committees.